IPV series (IPV-4K24U, IPV-6K48U, IPV-4K24U Pro, IPV-6K48U Pro, IPV-12K48U) — inverter fault code
Itel Energy 30 error code
Battery bank voltage is above the inverter's high-DC limit.
Likely causes
- Battery count or nominal voltage does not match the inverter model
- Battery type or charge-voltage setting wrong for the installed bank
- BMS or external charger overcharging the bank
- Battery connected while another source is charging it above the limit
Checks to run, in order
- 1Measure the battery voltage at the inverter terminals
- 2Count the batteries in series and compare with the model's nominal DC voltage
- 3Check the battery type and charge-voltage settings on the LCD
- 4Check BMS communication and reported voltage
Fixes
- Correct the battery bank configuration or replace it with the correct bank
- Correct the battery type and charge-voltage settings
- Stop charging, restart and confirm the code clears
When to escalate
If the measured bank voltage is within specification and code 30 persists, escalate for DC/DC board or BMS communication diagnosis.
Fix it with the right tools
Check the system around the fault before replacing parts: load, battery bank, PV string and commissioning settings. If you need a second opinion, send the code and your inverter model to our team.
Before you open the inverter
- Isolate both the AC and DC sides, then confirm the display is dead before touching terminals.
- Use insulated tools and one hand where possible. DC arcs do not self-extinguish like AC.
- If you see burnt terminals, swollen cells, leaking electrolyte or a burning smell, stop and escalate instead of resetting the fault.
Questions installers ask
What does Itel Energy 30 mean?
Battery bank voltage is above the inverter's high-DC limit.
How do I fix Itel Energy 30?
Correct the battery bank configuration or replace it with the correct bank Correct the battery type and charge-voltage settings Stop charging, restart and confirm the code clears
When should I escalate Itel Energy 30?
If the measured bank voltage is within specification and code 30 persists, escalate for DC/DC board or BMS communication diagnosis.
Can I reset Itel Energy 30 myself?
Only after isolating the AC and DC sides and running the checks above. If Itel Energy 30 returns immediately, stop resetting it and escalate; a repeating fault usually points to a real circuit, battery or hardware problem.
Which models show Itel Energy 30?
Itel Energy 30 is documented for IPV series (IPV-4K24U, IPV-6K48U, IPV-4K24U Pro, IPV-6K48U Pro, IPV-12K48U) — inverter fault code. Confirm the code on your own unit's display or manual before ordering parts.
More Itel Energy error codes
- Itel Energy 01Display code 01 covers two events: as a warning it signals output overload (flashing fault LED, two beeps per second); as a fault it signals DC bus over-voltage (solid fault LED, output switched off).
- Itel Energy 02Display code 02 covers two events: as a warning it signals the upper cooling fan is locked (three beeps); as a fault it signals DC bus under-voltage (solid fault LED, output switched off).
- Itel Energy 03Display code 03 covers two events: as a warning it signals the lower cooling fan is locked (three beeps); as a fault it signals that the DC bus soft-start sequence failed (solid fault LED).
- Itel Energy 04Grid voltage is above the upper limit of the inverter's grid window; warning only, with no buzzer alarm.
- Itel Energy 05In a parallel system the AC outputs of the units are not connected together, or a unit is running on a different phase.
- Itel Energy 06Remote shutdown is enabled, typically from the monitoring app over Wi-Fi, so the inverter is being held off remotely.
Guidance reviewed 17 October 2026 by the Mishka Energy installer team. Error codes vary by brand, model family and firmware; confirm against the manufacturer manual.
Back to troubleshooting