IPV series (IPV-4K24U, IPV-6K48U, IPV-4K24U Pro, IPV-6K48U Pro, IPV-12K48U) — inverter fault code
Itel Energy 40 error code
PV array open-circuit voltage is above the inverter's maximum PV input voltage.
Likely causes
- Too many PV modules connected in series per string
- Array open-circuit voltage rising in cold conditions
- String design not matched to the inverter's PV input rating
- Incompatible or mismatched modules in a string
Checks to run, in order
- 1Measure the string open-circuit voltage at the DC switch
- 2Count the modules per string and compare with the maximum input voltage on the datasheet
- 3Repeat the measurement on a cold morning when Voc is highest
Fixes
- Remove modules from the series string to bring Voc within the input rating
- Re-string the array to a compliant configuration
- Restart the inverter and confirm the fault clears
When to escalate
If the measured Voc is within the PV input rating and code 40 persists, escalate for PV input sensing service.
Fix it with the right tools
Check the system around the fault before replacing parts: load, battery bank, PV string and commissioning settings. If you need a second opinion, send the code and your inverter model to our team.
Before you open the inverter
- Isolate both the AC and DC sides, then confirm the display is dead before touching terminals.
- Use insulated tools and one hand where possible. DC arcs do not self-extinguish like AC.
- If you see burnt terminals, swollen cells, leaking electrolyte or a burning smell, stop and escalate instead of resetting the fault.
Questions installers ask
What does Itel Energy 40 mean?
PV array open-circuit voltage is above the inverter's maximum PV input voltage.
How do I fix Itel Energy 40?
Remove modules from the series string to bring Voc within the input rating Re-string the array to a compliant configuration Restart the inverter and confirm the fault clears
When should I escalate Itel Energy 40?
If the measured Voc is within the PV input rating and code 40 persists, escalate for PV input sensing service.
Can I reset Itel Energy 40 myself?
Only after isolating the AC and DC sides and running the checks above. If Itel Energy 40 returns immediately, stop resetting it and escalate; a repeating fault usually points to a real circuit, battery or hardware problem.
Which models show Itel Energy 40?
Itel Energy 40 is documented for IPV series (IPV-4K24U, IPV-6K48U, IPV-4K24U Pro, IPV-6K48U Pro, IPV-12K48U) — inverter fault code. Confirm the code on your own unit's display or manual before ordering parts.
More Itel Energy error codes
- Itel Energy 01Display code 01 covers two events: as a warning it signals output overload (flashing fault LED, two beeps per second); as a fault it signals DC bus over-voltage (solid fault LED, output switched off).
- Itel Energy 02Display code 02 covers two events: as a warning it signals the upper cooling fan is locked (three beeps); as a fault it signals DC bus under-voltage (solid fault LED, output switched off).
- Itel Energy 03Display code 03 covers two events: as a warning it signals the lower cooling fan is locked (three beeps); as a fault it signals that the DC bus soft-start sequence failed (solid fault LED).
- Itel Energy 04Grid voltage is above the upper limit of the inverter's grid window; warning only, with no buzzer alarm.
- Itel Energy 05In a parallel system the AC outputs of the units are not connected together, or a unit is running on a different phase.
- Itel Energy 06Remote shutdown is enabled, typically from the monitoring app over Wi-Fi, so the inverter is being held off remotely.
Guidance reviewed 17 October 2026 by the Mishka Energy installer team. Error codes vary by brand, model family and firmware; confirm against the manufacturer manual.
Back to troubleshooting